This service manual is written for use by qualified service personnel only. . The Kurzweil KR offers the same powerful features as the K including. Manuals and User Guides for Kurzweil K, KR. We have 5 Kurzweil K, KR manuals available for free PDF download: Supplement Manual, . View and Download Kurzweil K, KR service manual online. Service Manual. K, KR Synthesizer pdf manual download.

Author: Meztill Muktilar
Country: Laos
Language: English (Spanish)
Genre: Career
Published (Last): 6 November 2004
Pages: 91
PDF File Size: 13.89 Mb
ePub File Size: 19.49 Mb
ISBN: 882-2-57013-943-8
Downloads: 48248
Price: Free* [*Free Regsitration Required]
Uploader: Mikabei

In this manual, used primarily in reference to control sources.

The test takes approximately 20 aecondg for each Megabyte of RAM. It is possible for the headphone amplifier to clip at high volume slider settings. The transition should be smooth with no glitches. The values the LEDs represent are as follows: There’s also the Track kuzweil, fully editable, with features like ppq resolution and nondestructive track editing and groove quantizing.

Kurzweil K2000, K2000R Service Manual

Rechargeable batteries should not be used; the K will not recharge them and their life after charging on an external charger will be only a few months. If the observed value does not match the expected value, a data failure is indicated. Disk drive will now lift out of shell. D4 D-2, Schott ky diode clamps any overvoltage to no more than 0. Open the unit as described in Section 3.

Kurzweil K2000, K2000R Manuals

Pressing Open On Files Rafer to BlocJc Diagram Figure 5. Normally each test need only be run once in the attempt to identify failures. For the UO example, the control voltage is switched by an analog switch.

Note that setting the offset adjustment to a null point for the pop artifact may increase the noise floor.

Full text of “Kurzweil: K KR SERVICE MANUAL”

To enter the LED Scanner diagnostics, press and hold the 7, 8, and 9 buttons while the power is off then turn the power on while continuing to hold them down. Refer to figure 5. Saving Dependent Objects It switches off when you release the key, and any sustain controls you may have applied to the note Sustain or Sostenuto pedal, etc. Intonation Table Editor Plug in the power line cord, and turn the unit on. R and C stabilize the feedback loop to prevent oscillation of the regulator.


Be careful not to break this tab. Relink-by-name Processing Time Carbon-zinc batteries will last for at least a year after installation while alkaline batteries should last for at least 2 years provided they are installed before the date on the package. Slide the fuse block back onto the Phillips head screw and pedestal.

SCSI test will always fail without internal or external drive installed. Creating A Directory With Newdir The setting of the voltage selector can be seen just to the right of the power input receptacle on the back of the product. Plug headphone or single output device into LEFT mix jack, listen for proper output. Connect the power cord to the K first, then to a properly grounded three-prong power outlet.

The diagnostic can be used to check out the keyboard and built-in controls as well. To install a key simply reverse 3. Triggerchan trigger Channel Press the Disk mode button, then scroll through the files with the Alpha Wheel. The sine wave at 20 Hz is generated as soon as the test is initiated.

A type of distortion which occurs in digitally sampled sounds when higher pitches increased sample playback rates introduce partials that were not present in the original sound. It will explain how to use the K’s internal diagnostic software, describing the significance of success or failure of each of the individual tests, and when applicable, the measures required to correct test failures will be given.


Playback Mode playback Press the SIMM firmly into the socket until it clicks into place. For multi- timbral sequences on multiple MIDI channelsyou will need to do this for each channel. In the K case, the power transformer must also be oriented such that the filters are in a “null point” of the transformer’s flux field. Name, Save, Delete, And Dump A special power-up menu will appear see Figure 4. R86, R92, C, and C B-4 smooth sudden changes in the control voltage level to provide smooth, clickless changes in gain.

In this case, start by checking the components related to the first test that failed.

If one or more of the steps in this test indicate a failure, the problem is probably to be found in the connections between the chips and the CPU. Other professional features include stereo multi-effects capable of four simultaneous effects including reverb, chorus, delay, multi-tap delay, flange, rotary simulation and more.

View the discussion thread. This document is for use with K Diagnostic software Version 0.

Care should be taken to minimize the amount of dust in the environment. LCD will display “Testing Use the built-in 3. Using a 2 Phillips screwdriver, remove the 16 sheet metal screws securing the keyboard to the bottom of its enclosure. In a successful test, the eight LEDs to the manuak of the LCD will flash in sequence from top left to bottom left to top right to bottom right at ms intervals.

Author: admin